KIES WHAT IS MY DEVICE NAME UPDATE
Please comment below if you know what this is used for and I will update the “Guide” accordingly! #6 “UMS Button” It is »UNKNOWN« this time to me what this button is used for. This is used for almost all the »»REPAIR«« procedures.This is the most commonly used button for “Novice Users” #5 “CSC Button” This button is used to »✿LASH«« “Complete” or “Partial” images that use the Device’s “Product Code” (CSC). This button was previously labeled as “Phone”.
#4 “CP Button” - This button is used to »✿LASH«« “Individual Sections” of the Device’s Hardware.
This button was previously labeled as “PDA”. #3 “AP Button” - This button is used to »✿LASH«« “Individual Sections” of the Device’s Operating System (OS). ««« This MUST ONLY be used with the CORRECT type of “Image File”!!!! »»» You would »✼lick«« this button if you wanted to »✿LASH«« only a portion or ✺LL« of the Device’s “Firmware”. #2 “BL Button” - This button is an abbreviation for “Bootloader”. This is used to »»REPAIR«« the Device’s “Storage” (eMMC) and is used with the “Re-Partition” checkbox. #1 “PIT Button” - This is the button you would »✼lick«« to »»SELECT«« a “Partition Information Table (PIT)” file to use during the procedure or »✿LASH««. Let me now explain “What” each button is, and “What” it is used for : These buttons are used for different purposes during the »✿LASH«« or »»REPAIR«« Procedure. Also, you will notice that on the Right-Hand Side there are multiple “Buttons” with different labels. These “Options” are only ✺VAILABLE« if the “Image 5” supports these “Options”. You will also notice that some of these “Options” are “Greyed Out”, or »NOT AVAILABLE«. Looking at the image above, notice that there are multiple “Options” or “Check-Boxes” located inside the »Upper-Left« quadrant (Area) of the Program Window. ** IF ** You ✽O NOT« see any “Information” inside ✺NY« of the “Smaller” boxes, your Device »IS NOT« connected properly to your Computer!!! You will need to »✽OWNLOAD«« and »»INSTALL«« the latest Samsung Device Drivers.
KIES WHAT IS MY DEVICE NAME SOFTWARE
The ODIN software can handle up to Eight (8) Devices of the “Same” model One (1) time!! These boxes will indicate the “Attached Devices” that are connected to the Computer, and what “Port” they are connected too. Underneath the “Large” boxes, there is a horizontal »ROW« of “Smaller” boxes. This is “Where” the software will indicate the progress of a procedure, and for each Device that is connected to the Computer. Looking at the image above, notice that there is a horizontal »ROW« of Eight (8) “Large” boxes across the “Top” of the Program Window. In addition, This software can also be used to »»UPGRADE«« a Device’s “Operating System” (OS) to the ✼URRENT REVISION«. This software is also used to »»REPAIR«« a Device that may be experiencing issues due to any software corruption, an “Error” that occurs ✺FTER« an “Over the Air” (OTA) update, or any »»ROOTING«« activities!! The ODIN software is a »VERY« useful, and »POWERFUL«, “Tool” that allows a “User” to »✿LASH««, or “Program” a Device, or multiple Devices, ✼OMPLETELY« back to the “Factory Specifications” (Factory Data Reset + File Corrections). This is what the Software looks like when you »»OPEN«« the program : ** IF ** You find any discrepancies, or errors.PLEASE, LET ME KNOW!!
I hope this helps you to solve your problems, or at least learn something NEW!! I work HARD to help everyone out!! Thank YOU so much for taking the time, and effort, to read and/or use my Guide!! HELLO!!! Welcome to my «» Kaotic World «»!!!